Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).
2018-12-18u2002·u2002about the performance of your brake system. TRAILER BREAKAWAY SYSTEM All actuators must have a way to apply the trailer brakes should the trailer become completely detached from the towing vehicle. The breakaway cable is the third line of defense after trailer separation. Before the breakaway cable is pulled, the
Get PriceTrailer Plugs and Sockets. Narva 7 and 12 pin trailer connectors comply with all relevant ADRs. Flat connectors comply with Australian Standards AS4177.5-2004. Large and small round connectors comply with AS2513-1982 while Heavy duty connectors meet the AS4735-2003 standard as required for vehicles and trailers over 3.5 tonnes.
Get Price2019-7-26u2002·u2002Brake pressure for BrakeRite EHB & BrakeRite II SD is controlled by most in-cab electronic brake controllers. BrakeRite II RF has an in-cab controller provided. Brake performance is selected by driver. Manual override can also be applied if …
Get Price2013-8-21u2002·u2002www.cequentgroup.com ©2012 Cequent Performance Products, Inc. P/N 98931-2013 Rev. A. 11/12 for 2013 485 BRAKE CONTROLS BRAKE CONTROLS - TECHNICAL WIRING INSTRUCTIONS FOR ELECTRONIC BRAKE CONTROLS P/N 4399 REV K Generic Wiring Diagram
Get Price2016-3-16u2002·u2002The Trailer Disconnected Warning on our new P3 Brake Controller had nothing with the fine job done by Performance Trailer Braking.In fact, John came back out and messed with the plug and socket terminals to fix the problem. The issue returned a few days later.
Get Price2015-1-21u2002·u2002Trailer Brake Control Module (TBC) Installation 1. Remove the center LH Instrument Panel (IP) finish panel. For additional information, refer to Workshop Manual (WSM) Section 501-12. 2. Remove the IP storage bin. 1 Disengage the two clips on the top of the storage bin that retain it into the IP.
Get PriceThe trailer brakes should be adjusted as follows: after the first 200 miles of operation when the brake shoes and drums have 'seated,' at 3,000 mile intervals, or as use and performance requires. The brakes should be adjusted in the following manner: 1. Jack up the trailer and secure on adequate capacity jack stands. Follow the trailer manu-
Get PriceNow if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way. If you do have trailer brakes you would need the # ETBC7 instead of the # 37185 and a brake controller. This kit comes with everything needed to wire up the 7-way and install a brake controller.
Get Price2019-5-16u2002·u2002Step 9: Get the new cables and install them by sliding the rear cable through the backing plate then attach them to the emergency brake lever. Step 10: Put the brake drum and brake disc assembly back to their original location. Attach the wheel and tire. Step 11: Lower the vehicle and torque the lug nuts to 100 ft. lbs. Step 12: Connect the rear cables to the equalizer and properly route them ...
Get PriceTrailer Cable. Trailer cable is a multi-conductor cable that is available in either 4 conductor, 6 conductor, or 7 conductor arrangements. Sold in either pre-cut lengths, or available in spools. Manufactured with a PVC over-all jacket outside and general purpose primary wire inside. The single conductors are stranded copper, and each conductor ...
Get Price2013-3-22u2002·u2002Minimum Hookup Wire Size (Copper) 1 AWG 4 Under 30 1 AWG 4 30-50 10 AWG 6 Under 30 10 AWG 6 30-50 8 AWG-1 -Synchronizing Your Trailer Brakes To insure safe brake performance and synchronization, read the brake controller manufacturer's instructions completely before attempting any synchronization procedure. ... Jack up trailer and secure on ...
Get Price2019-2-22u2002·u2002This cable will need to be connected separately to the tow vehicle but not to the safety chains or ball mount. The purpose of this cable is to attach the trailer brake system to your tow vehicle. If your trailer were to come unhitched from your truck, the breakaway cable would then pull the pin out and engage the trailer brakes. This would slow ...
Get Price2016-9-7u2002·u2002Check trailer for proper towing attitude. A loaded or unloaded trailer must be towed with a positive hitch height for a safe towing. When the hook-up is slightly higher compared to the leveling of the trailer, a smoother performance is given. Connect electrical plug, check lights by …
Get Price2016-8-15u2002·u2002about the performance of your brake system. TRAILER BREAKAWAY SYSTEM All actuators must have a way to apply the trailer brakes should the trailer become completely detached from the towing vehicle. The breakaway cable is the third line of defense after trailer separation. Before the breakaway cable is pulled, the
Get PriceThe trailer brakes should be adjusted as follows: after the first 200 miles of operation when the brake shoes and drums have 'seated,' at 3,000 mile intervals, or as use and performance requires. The brakes should be adjusted in the following manner: 1. Jack up the trailer and secure on adequate capacity jack stands. Follow the trailer manu-
Get Price2021-11-29u2002·u2002Part Number: ST-UFP35112. Only. $39.99. UFP Breakaway Safety Cable Assembly for UFP Models XR-84 DIsc and Drum Brake Actuators 40024K 071-197-00. Part Number: ST-UFP40024K. Only. $23.99. UFP Breakaway Safety Cable Assembly for UFP A-60 Disc and Drum Brake Actuators 32264K 071-195-00. Part Number: ST-UFP32264.
Get Price2015-1-21u2002·u2002Trailer Brake Control Module (TBC) Installation 1. Remove the center LH Instrument Panel (IP) finish panel. For additional information, refer to Workshop Manual (WSM) Section 501-12. 2. Remove the IP storage bin. 1 Disengage the two clips on the top of the storage bin that retain it into the IP.
Get Price2021-11-25u2002·u2002Apply the trailer parking brake. Remove and stow the trailer number plate and lower the landing legs. Disconnect all of the air and electrical services and stow safely. Remove the security 'dog clip' and pull the release handle to disengage the 5th wheel jaws. Slowly draw the tractor unit away from the trailer. If the tractor unit has ...
Get Price
